HD05 12-HEAD STAINLESS STEEL MIST MAKER WITH TRANSFORMER
Main Features
Mist maker utilizes electrical oscillation at ultrasonic frequnecies. The ceramic changes electrical oscillation into mechanical oscillation, which creates the mist and water spray. This oscillation also produces negative ions, which help to freshen air and the mist will increase the humidity level to a room.
- Comes with 12 pcs spray unit, bring huge quantity of mist.
- Comes with 'Water-Level Sensor' and new 'Improved Unscratchable Ceramic Smart Disc'.
- Safe low voltage, harmless to human and animal.
Rated Voltage
|
Input: 230V/50Hz or 120V/60Hz
Output: AC36V 300W
|
Consumption Power
|
≤8.2A
|
Mist Head Dimension
|
Φ150mm x H55mm
|
Cable Length
|
10 m
|
Working water temperature
|
+5 ̴ 50 degree Celcius
|
Water rate
|
≥5300ml/hour
|
Depth of water limited
|
30 ̴ 50mm (from surface of ceramic)
|
Mist Maker Safety instructions, read before
initial operation
1. Verify the voltage rate of the transformer with the local power supply before use.Use only the transformer and accessories supplied with the mist maker.
2. Do not touch the ceramic disc of mist maker while in operation.
3. Always disconnect the power supply before moving or maintenance.
4. Do not allow transformer, connector and controller on the cable to get wet or gather moisture.
5. Do not allow the mist maker unit electrical plug connector to get wet.
6. Do not place a container, cup, cover or any other object over the mist maker unit that completely covers the mist maker. Water must be allowed to circulate around the unit for cooling.
7. Do NOT run it outside water.
1. Verify the voltage rate of the transformer with the local power supply before use.Use only the transformer and accessories supplied with the mist maker.
2. Do not touch the ceramic disc of mist maker while in operation.
3. Always disconnect the power supply before moving or maintenance.
4. Do not allow transformer, connector and controller on the cable to get wet or gather moisture.
5. Do not allow the mist maker unit electrical plug connector to get wet.
6. Do not place a container, cup, cover or any other object over the mist maker unit that completely covers the mist maker. Water must be allowed to circulate around the unit for cooling.
7. Do NOT run it outside water.
8.
Forbid to touch water level sensor when the mist maker is working.
9.The
transformer will heat up during operation. Make sure there is sufficient
ventilation. Do not cover the housing.
10.
Avoid placong it in the immediate vicinity of electric appliances or
water-sensitive objects since a few water splashes might be produced.
Instructions for use
1. Place the mist unit into a water container placidly. No matter the size of the container, there should be approximately 10mm of water above the water level sensor of mist unit. The deeper unit sits in the water, the less the mist coming out.
Instructions for use
1. Place the mist unit into a water container placidly. No matter the size of the container, there should be approximately 10mm of water above the water level sensor of mist unit. The deeper unit sits in the water, the less the mist coming out.
NOTE: The mist maker just need ordinary tap water. However depending on your local water, it may be best to use filtered drinking water as it can increase the life of your ceramic disk and reduce scale.
The water-level sensor will not operate properly when the water level is low and it may resulting the mist maker exhausted to a point of burn out or function improperly.2. Connect the power cable leading from the mist unit to the power cable of the the transformer unit.
3. Plug the transformer unit into the A/C power socket. A light on the mist unit indicates the mist unit in on. If installed properly, it will begin producing the mist immediately.
General suggestions for optimum use
1. Do not operate fogger more than 8 hours per day. Connecting the transformer to a timer will insure your mist unit operating only when needed.
2. The mist unit sends up small jets of water while in operation. Your container should be large enough to provent water from splashing outside the container. Otherwise you need a water splash guard. Do not place the unit where water spillage or condensation will cause damage to furniture, electronic products or floors.
3. Use of clean water is recommended. When the water is dirty, change it with clean water in time(dirty water will affect normal misting production).
4. Do not use household abrasive cleaners on any part of the mist unit. You may clean it with soft cloth in clean water.
Maintenance
Note: Ceramic disc replacement kit sold seperately.
Follow the instruction below to change the disc:
1. Unplug the fogger power and remove fogger from water container, dry it with soft cloth.
2. Using the replacement disc/key tool, insert the key into the winding ring and turn counter clockwise.
3. Remove the filler piece(washer) and ceramic disc.
IMPORTANT: note that there is a front and back of the ceramic. Be sure to reinstall with the correct side(No black color ring side) facing up.
4. Clean mineral deposits on the ceramic with a sofe cloth and reinstall it or proceed to install a new ceramic disk in the reverse order of the above.
5. The inside area of the mist unit cavity must be completely dry before the parts are installed.
Parts/Accessories
HA14 MIST MAKER FLOAT (BUOY) FOR 12-HEAD MIST MAKER
Buoy size:
11"(outside diameter) x 6.14"(inside diameter) x 3"(h)
Demonstration
